Diamond Raman laser promising for imaging, ophthalmology, cancer therapy
OCTOBER 14, 2008 -- Researchers at the Institute of Photonics, University of Strathclyde (Glasgow, Scotland) have begun a 3.5 year project to develop a novel solid-state laser incorporating CVD (chemical vapor deposition) diamond manufactured by Element Six Ltd. (Ascot, UK). The expected result is small, compact lasers with superior power handling and the ability to operate at currently unavailable wavelengths. Diamond Raman lasers could enable new applications in medical imaging, eye disease diagnosis and therapy, cancer treatment, and multispectral imaging.
Diamond's unique combination of optical and thermal properties can be exploited through Element Six's single crystal CVD material. A vital property of the diamond supplied by Element Six is that it exhibits ultra-low birefringence.
The project will be led by Dr. Alan Kemp at the Institute of Photonics, University of Strathclyde, and supported by a grant of more than GPB600,000 from the UK government-funded Engineering and Physical Sciences Research Council (EPSRC). Element Six is to supply the research team with high quality single crystal CVD diamond for the duration of the project.
The Institute of Photonics and Element Six have previously worked together on the government supported MIDDI project under which has led to the ability to carry out precision etching of single crystal diamond micro-optics, for example.
How Raman lasers work
Raman lasers make use of a phenomenon called Raman Scattering discovered in 1922. When photons hit a substance, a tiny fraction of them interact by causing the atoms of the substance to vibrate. In such 'inelastic' collisions, the photons gain or lose specific amounts of energy, resulting in light of a different wavelength. A Raman laser amplifies the secondary light by oscillating it and pumping energy into the system to emit a coherent laser beam.
The importance of this type of laser is that it can shift the wavelength. As Dr. Kemp says, the ability to shift the wavelengths "gives access to the applications-rich, but currently source-poor, yellow-orange region of the spectrum." Today, most commercial lasers operate in the near infrared region of the spectrum between 0.8 microm to 1.1 microm with a particular concentration around 1 microm (1.03 - 1.07 microm) where most of the high performance laser work is done. "Perhaps the most important challenge in modern solid-state laser engineering," says Dr. Kemp, "is to find ways to generate new wavelengths but in doing so to retain as much as possible of the convenience and performance of current lasers."
Potential of synthetic diamond
In addition, current generations of continuous wave solid state silicon Raman lasers have been limited to powers of only a few watts due to thermal problems. Diamond has excellent thermal conductivity combined with a low thermal coefficient of expansion allowing greater power handling capability. "The least glamorous but most pervasive problem in laser engineering, particularly when you want high performance in a small package, is how to deal with heat," points out Dr. Kemp. "This is particularly problematic in high power Raman lasers because crystals that are good Raman converters are typically rather poor conductors of heat. This is where diamond comes in. With a thermal conductivity that is two to three orders of magnitude better than typical Raman active crystals, it should be an excellent Raman medium and allow us to generate much higher output powers." In addition, diamond shifts the wavelength slightly further than the Raman-active crystals that are currently used which may extend its application potential. "The team at the Institute of Physics has recognised that diamond has a high Raman gain coefficient and a large Raman shift compared to conventional Raman media," adds Chris Wort, Technical Manager at Element Six.
Element Six's material exhibits ultra-low birefringence -- which is the effect that happens when the speed of light in a medium varies if the polarisation of the light changes. This has to be carefully controlled in a laser cavity in order to make the laser work well. Dr. Kemp says, "The ultra-low birefringence single crystal CVD diamond that E6 produces is a real step forward for all photonics applications of diamond, particularly laser applications. It allows us to exploit the exceptional properties of diamond without compromising other aspects of the laser's performance."
Element Six calls itself the world's leading supplier of high quality supermaterials used throughout manufacturing industry for a wide range of applications. The Institute of Photonics, established in 1995, is a commercially oriented research unit, part of the University of Strathclyde. Its key objective is to bridge the gap between academic research and industrial applications and development in the area of photonics.
More information:
Element Six