Near-field optical microscopy images intersubband transitions in few-layer 2D materials

Aug. 28, 2018
Results could be applicable to future quantum-cascade lasers (QCLs) and infrared photodetectors (QWIPs).

Semiconducting heterostructures have been key to the development of electronics and optoelectronics. Many applications in the infrared and terahertz frequency ranges exploit transitions called intersubband transitions between quantized states in semiconductor quantum wells.

These intraband transitions exhibit very large oscillator strengths, close to unity. Their discovery in III-V semiconductor heterostructures depicted a huge impact within the condensed matter physics community and triggered the development of quantum-cascade lasers (QCLs) and quantum-well infrared photodetectors (QWIPs).

Quantum wells of the highest quality are typically fabricated by molecular-beam epitaxy (sequential growth of crystalline layers), a well-established technique. However, it poses two major limitations: Lattice-matching is required, restricting the freedom in materials to choose from, and the thermal growth causes atomic diffusion and increases interface roughness.

2D materials can overcome these limitations since they naturally form a quantum well with atomically sharp interfaces. They provide defect free and atomically sharp interfaces, enabling the formation of ideal QWs, free of diffusive inhomogeneities. They do not require epitaxial growth on a matching substrate and can therefore be easily isolated and coupled to other electronic systems such as silicon CMOS or optical systems such as cavities and waveguides.

Surprisingly enough, intersubband transitions in few-layer 2D materials had never been studied before, neither experimentally nor theoretically. Thus, in a recent study published in Nature Nanotechnology, ICFO researchers Peter Schmidt, Fabien Vialla, Mathieu Massicotte, Klaas-Jan Tielrooij, Gabriele Navickaite, led by ICREA Prof at ICFO Frank Koppens, in collaboration with the Institut Lumière Matière - CNRS, Technical University of Denmark, Max Planck Institute for the Structure and Dynamics of Matter, CIC nanoGUNE, and the National Graphene Institute, report on the first theoretical calculations and first experimental observation of inter-sub-band transitions in quantum wells of few-layer semiconducting 2D materials (TMDs).1

Directly observing intersubband resonances

In their experiment, the team of researchers applied scattering scanning near-field optical microscopy (s-SNOM) as an approach for spectral-absorption measurements with a spatial resolution below 20 nm. They exfoliated TMDs, which comprised terraces of different layer thicknesses over lateral sizes of about a few micrometers. They directly observed the intersubband resonances for these different quantum well thicknesses within a single device. They also electrostatically tuned the charge-carrier density and demonstrated intersubband absorption in both the valence and conduction bands. These observations were complemented and supported with detailed theoretical calculations revealing many-body and nonlocal effects.

The results of this study pave the way towards an unexplored field in this new class of materials and offer a first glimpse of the physics and technology enabled by intersubband transitions in 2D materials, such as infrared detectors, sources, and lasers with the potential for compact integration with silicon CMOS.

Source: https://www.icfo.eu/newsroom/news/article/4092

REFERENCE:

1. Peter Schmidt et al., Nature Nanotechnology (2018); https://doi.org/10.1038/s41565-018-0233-9.

About the Author

John Wallace | Senior Technical Editor (1998-2022)

John Wallace was with Laser Focus World for nearly 25 years, retiring in late June 2022. He obtained a bachelor's degree in mechanical engineering and physics at Rutgers University and a master's in optical engineering at the University of Rochester. Before becoming an editor, John worked as an engineer at RCA, Exxon, Eastman Kodak, and GCA Corporation.

Sponsored Recommendations

Optical Power Meters for Diverse Applications

April 30, 2024
Bench-top single channel to multichannel power meters, Santec has the power measurement platforms to meet your requirements.

Request a quote: Micro 3D Printed Part or microArch micro-precision 3D printers

April 11, 2024
See the results for yourself! We'll print a benchmark part so that you can assess our quality. Just send us your file and we'll get to work.

Request a Micro 3D Printed Benchmark Part: Send us your file.

April 11, 2024
See the results for yourself! We'll print a benchmark part so that you can assess our quality. Just send us your file and we'll get to work.

Request a free Micro 3D Printed sample part

April 11, 2024
The best way to understand the part quality we can achieve is by seeing it first-hand. Request a free 3D printed high-precision sample part.

Voice your opinion!

To join the conversation, and become an exclusive member of Laser Focus World, create an account today!