Light pulses control graphene's electrical behavior; finding could lead to new broadband light sensors

Aug. 1, 2014
Graphene has become a focus of research for a variety of potential uses in photonics; now, researchers at the Massachusetts Institute of Technology (MIT; Cambridge, MA) have found a way to control how the material conducts electricity by using extremely short light pulses, which could enable its use as a broadband light detector.

Graphene has become a focus of research for a variety of potential uses in photonics; now, researchers at the Massachusetts Institute of Technology (MIT; Cambridge, MA) have found a way to control how the material conducts electricity by using extremely short light pulses, which could enable its use as a broadband light detector.1

The researchers found that by controlling the concentration of electrons in a graphene sheet, they could change the way the material responds to a short but intense light pulse. If the graphene sheet starts out with low electron concentration, the pulse increases the material's electrical conductivity. This behavior is similar to that of traditional semiconductors, such as silicon and germanium.

But if the graphene starts out with high electron concentration, the pulse decreases its conductivity, which is how a metal usually behaves. Therefore, by modulating graphene's electron concentration, the researchers could effectively alter graphene's photoconductive properties from semiconductorlike to metallike.

The finding also explains the photoresponse of graphene reported previously by different research groups, which studied graphene samples with differing concentration of electrons. "We were able to tune the number of electrons in graphene, and get either response," says Alex Frenzel, one of the researchers.

Optical-pump terahertz-probe spectroscopy

To perform this study, the team deposited graphene on top of an insulating layer with a thin metallic film beneath it; by applying a voltage between graphene and the bottom electrode, the electron concentration of graphene could be tuned. The researchers then used optical-pump terahertz-probe spectroscopy, illuminating the graphene with a strong light pulse and measuring the change of electrical conduction by assessing the transmission of a second, terahertz light pulse.

The all-optical method avoids the need for adding extra electrical contacts to the graphene. Additionally, the short light pulses allow the researchers to change and reveal graphene's electrical response in only about a picosecond.

The researchers say the work could aid the development of new light detectors with ultrafast response times and high sensitivity across a wide range of light frequencies, from the infrared to ultraviolet. However, while the material is sensitive to a broad range of frequencies, the actual percentage of light absorbed is small; practical application of such a detector would therefore require increasing absorption efficiency, such as by using multiple layers of graphene, says researcher Nuh Gedik.

Source: http://www.eurekalert.org/pub_releases/2014-08/miot-lpc073114.php

REFERENCE:

1. A. J. Frenzel et al., Physical Review Letters (2014); doi: http://dx.doi.org/10.1103/PhysRevLett.113.056602

About the Author

John Wallace | Senior Technical Editor (1998-2022)

John Wallace was with Laser Focus World for nearly 25 years, retiring in late June 2022. He obtained a bachelor's degree in mechanical engineering and physics at Rutgers University and a master's in optical engineering at the University of Rochester. Before becoming an editor, John worked as an engineer at RCA, Exxon, Eastman Kodak, and GCA Corporation.

Sponsored Recommendations

Understanding 3D Printing Tolerances: A Guide to Achieving Precision in Additive Manufacturing

March 28, 2024
In the world of additive manufacturing, precision is paramount. One crucial aspect of ensuring precision in 3D printing is understanding tolerances. In this article, we’ll explore...

Horizon Microtechnologies: Coating 3D Printed Parts with Functional Materials

March 28, 2024
Andreas Frölich from Horizon Microtechnologies talks innovations in 3D micro-parts printing with functional materials for various industries.

Melles Griot® XPLAN™ CCG Lens Series

March 19, 2024
IDEX Health & Science sets a new standard with our Melles Griot® XPLAN™ CCG Lens Series fluorescence microscope imaging systems. Access superior-quality optics with off-the-shelf...

Spatial Biology

March 19, 2024
Spatial Biology refers to the field that integrates spatial information into biological research, allowing for the study of biological systems in their native spatial context....

Voice your opinion!

To join the conversation, and become an exclusive member of Laser Focus World, create an account today!