MIT multilayer device filters light based on direction of travel

March 28, 2014
MIT researchers have produced a filter that allows light of any color to pass through only if it is coming from one specific angle and reflect all light coming from other directions.

While it has long been possible to selectively filter light according to its color or polarization, selectivity based on the direction of propagation has remained elusive. But Massachusetts Institute of Technology (MIT; Cambridge, MA) researchers have produced a system that allows light of any color to pass through only if it is coming from one specific angle; the technique reflects all light coming from other directions. This new optical filter approach could ultimately lead to advances in solar photovoltaics, detectors for telescopes and microscopes, and privacy filters for display screens.

The work is described in a paper appearing in the journal Science written by MIT graduate student Yichen Shen, professor of physics Marin Soljačić, and four others. "We are excited about this," Soljačić says, "because it is a very fundamental building block in our ability to control light." The work is also described in a video at http://youtu.be/Lr9AAvRlQ54.

RELATED ARTICLE: EUV mirror shows near-zero reflectance at CO2 laser wavelength

The new structure consists of a stack of ultrathin layers of two alternating materials where the thickness of each layer is precisely controlled. "When you have two materials, then generally at the interface between them you will have some reflections," Soljačić explains. But at these interfaces, "there is this magical angle called the Brewster angle, and when you come in at exactly that angle and the appropriate polarization, there is no reflection at all."

While the amount of light reflected at each of these interfaces is small, by combining many layers with the same properties, most of the light can be reflected awayexcept for that coming in at precisely the right angle and polarization. Using a stack of about 80 alternating layers of precise thickness, Shen says, “We are able to reflect light at most of the angles, over a very broad band [of colors]: the entire visible range of frequencies.”

Previous work had demonstrated ways of selectively reflecting light except for one precise angle, but those approaches were limited to a narrow range of colors of light. The new system’s breadth could open up many potential applications, the team says.

Shen says, "This could have great applications in energy, and especially in solar thermophotovoltaics"harnessing solar energy by using it to heat a material, which in turn radiates light of a particular color. That light emission can then be harnessed using a photovoltaic cell tuned to make maximum use of that color of light. But for this approach to work, it is essential to limit the heat and light lost to reflections, and re-emission, so the ability to selectively control those reflections could improve efficiency."

The findings could also prove useful in optical systems, such as microscopes and telescopes, for viewing faint objects that are close to brighter objectsfor example, a faint planet next to a bright star. By using a system that receives light only from a certain angle, such devices could have an improved ability to detect faint targets. The filtering could also be applied to display screens on phones or computers, so only those viewing from directly in front could see them.

In principle, the angular selectivity can be made narrower simply by adding more layers to the stack, the researchers say. For the experiments performed so far, the angle of selectivity was about 10 degrees; roughly 90 percent of the light coming in within that angle was allowed to pass through. While these experiments were done using layers of glass and tantalum oxide, Shen says that in principle any two materials with different refractive indices could be used.

John Pendry, a professor at Imperial College London who was not connected to this research, calls this an "ingenious application. On a macroscopic scale this is equivalent to observing the world through a set of louvers … that allow light to enter from one direction only," Pendry says. "However, the new device is infinitely more refined, operating as it does on the length scale of a wavelength."

The team also included MIT research scientist Ivan Celanovic; associate professor of mathematics Steven Johnson; John Joannopoulos, the Francis Wright Davis Professor of Physics; and Dexin Ye of Zhejiang University in China. The work was supported in part by the Army Research Office, through MIT’s Institute for Soldier Nanotechnologies, and the U.S. Department of Energy, through the MIT S3TEC Energy Research Frontier Center.

SOURCE: MIT; http://web.mit.edu/newsoffice/2014/a-new-angle-on-controlling-light.html

About the Author

Gail Overton | Senior Editor (2004-2020)

Gail has more than 30 years of engineering, marketing, product management, and editorial experience in the photonics and optical communications industry. Before joining the staff at Laser Focus World in 2004, she held many product management and product marketing roles in the fiber-optics industry, most notably at Hughes (El Segundo, CA), GTE Labs (Waltham, MA), Corning (Corning, NY), Photon Kinetics (Beaverton, OR), and Newport Corporation (Irvine, CA). During her marketing career, Gail published articles in WDM Solutions and Sensors magazine and traveled internationally to conduct product and sales training. Gail received her BS degree in physics, with an emphasis in optics, from San Diego State University in San Diego, CA in May 1986.

Sponsored Recommendations

Achieving Ultralow-Loss Photonics Array Alignment

Feb. 23, 2024
Two- and three-dimensional photonics arrays are commonly used for coupling light in photonic integrated circuits. With the increasing demand for ultralow-loss transmission in ...

Control Techniques in Laser Processing

Feb. 23, 2024
A laser processing tool is only as good as the motion equipment underneath it. One must first consider design characteristics of a motion platform, and second, advanced control...

High-Precision Laser Processing for Medical Device Manufacturing

Feb. 23, 2024
Laser processing has been used for decades to manufacture tubular medical devices, such as stents, valves, and vascular grafts. However, achieving the precision that is necessary...

Selecting Optimal Positioning Equipment for Laser Direct-Write Processes

Feb. 23, 2024
Choosing the optimal automation equipment for a given process requires a thorough understanding of the process parameters and the effects of positioning errors on the results....

Voice your opinion!

To join the conversation, and become an exclusive member of Laser Focus World, create an account today!