Business Forum: How feasible is it to raise funds in the US from my current location?

April 1, 2011
It is very difficult to get venture funding in my country because there are only two VC firms and both are small and extremely risk averse. Is it possible to raise venture capital in the United States to start a photonics company here?
1304qa Chang New
1304qa Chang New
1304qa Chang New
1304qa Chang New
1304qa Chang New

Q: It is very difficult to get venture funding in my country because there are only two VC firms and both are small and extremely risk averse. Is it possible to raise venture capital in the United States to start a photonics company here?

A: I don't want to discourage you from trying because an entrepreneur is expected to be persistent and never accepts no for an answer. I believe it would be very difficult, if not impossible, but let us also discuss what you might do to gain traction with potential investors on US soil.

Advice that is frequently given to investors is to "invest within your area code." The point is communicating is difficult enough even with face-to-face discussion and site visits, let alone having to communicate by phone, e-mail, or even video conferencing. Most VC firms hardly ever invest in a company that they cannot easily visit. To avoid this problem, they would even set up a branch office perhaps in Shanghai, Beijing, or London. The hurdle in your case is it will take close to 30 hours to get to your place from the West Coast and there are not many investment opportunities in your country to justify setting up a branch office.

You might be able to entice some investors here if you can prove your team is good at product development, and that your long-term goal is to have an R&D facility in your country and business development headquarters in the US close to your main market and investors . To achieve that, you need to develop the product and get a few orders so you can validate the market potential. Figure out a way to get seed funding from your local VCs, angel investors, and government agencies to get the ball rolling.

Q: In one of your speeches, you said generalists cannot compete and you also said to become broadly knowledgeable. Isn't this a contradiction?

A: To avoid this confusion, I should have said to become a specialist and also take initiative to become broadly knowledgeable. We are always competing with specialists anywhere we go, whether for a job or for business development. And the specialists are likely to be the winners given that they have the expertise. Being broadly knowledgeable enables you to draw from what you know to make sound decisions, recognize opportunities, and sell your position effectively.

It benefited me greatly to have started reading the Wall Street Journal, Business Week, Fortune, and Forbes regularly when I was a graduate student. I have hardly ever missed an issue since then. The eclectic information I picked up over the years enabled me to draw analogies that helped in making business decisions.

Analogy is useful because business is about dealing with people who have similar motivations. For example, you may recall holographic interferometry was being promoted in the '70s for testing the integrity of aircraft tires. Even minute defects deep inside the tire become visible by using lasers to make two sequential holograms of a tire with a small perturbation between shots. Tire companies rejected this technique, claiming it was too cumbersome, until FAA mandated that every rethread tire must be tested after a DC 10 crash-landed in Los Angeles International Airport with multiple-tire blowout. The speculation in the laser community is that tire companies did not want to have a record to be used in court as evidence that they knowingly sold defective parts. With this episode in mind, I have avoided investing in any quality-control company, even in software to monitor the effectiveness of an information system, to give one example. My reasoning is it will be a hard sell because someone will always resist the product in order to avoid being identified as a culprit if any deficiency is found. Always understand how purchasing decisions are made. In this example, the IT manager responsible for operating the system is also a decision maker who could buy your product.

About the Author

Milton Chang

MILTON CHANG of Incubic Management was president of Newport and New Focus. He is currently director of mBio Diagnostics and Aurrion; a trustee of Caltech; a member of the SEC Advisory Committee on Small and Emerging Companies; and serves on advisory boards and mentors entrepreneurs. Chang is a Fellow of IEEE, OSA, and LIA. Direct your business, management, and career questions to him at [email protected], and check out his book Toward Entrepreneurship at www.miltonchang.com.

Sponsored Recommendations

How Precision Motion Systems are Shaping the Future of Semiconductor Manufacturing

March 28, 2024
This article highlights the pivotal role precision motion systems play in supporting the latest semiconductor manufacturing trends.

Understanding 3D Printing Tolerances: A Guide to Achieving Precision in Additive Manufacturing

March 28, 2024
In the world of additive manufacturing, precision is paramount. One crucial aspect of ensuring precision in 3D printing is understanding tolerances. In this article, we’ll explore...

Automation Technologies to Scale PIC Testing from Lab to Fab

March 28, 2024
This webinar will cover the basics of precision motion systems for PIC testing and discuss the ways motion solutions can be specifically designed to address the production-scale...

Case Study: Medical Tube Laser Processing

March 28, 2024
To enhance their cardiovascular stent’s precision, optimize throughput and elevate part quality, a renowned manufacturer of medical products embarked on a mission to fabricate...

Voice your opinion!

To join the conversation, and become an exclusive member of Laser Focus World, create an account today!