Ultrafast optical shutter is switched entirely by laser light

Dec. 9, 2007
Nashville, TN--Researchers from Vanderbilt University and the University of Konstanz (Konstanz, Germany) report that a near-infrared laser can be used to switch a film of vanadium dioxide back and forth between reflective and transparent states without heating or cooling it.

Nashville, TN--Researchers from Vanderbilt University and the University of Konstanz (Konstanz, Germany) report that a near-infrared laser can be used to switch a film of vanadium dioxide back and forth between reflective and transparent states without heating or cooling it.

It is one of the first cases that scientists have found where light can directly produce such a physical transition without changing the material's temperature. The study was conducted by a team of physicists from Vanderbilt University and the University of Konstanz headed by Richard Haglund of Vanderbilt and Alfred Leitenstorfer from Konstanz.

It is also among the most recent examples of coherent control, the use of coherent radiation like laser light to affect the behavior of atomic, molecular or electronic systems. The technique has been used to control photosynthesis and is being used in efforts to create quantum computers and other novel electronic and optical devices. This discovery opens the possibility of a new generation of ultrafast optical switches for communications.

Vanadium dioxide's uncanny ability to switch back and forth between transparent and reflective states is well known. At temperatures below 154 degrees F, vanadium dioxide film is a transparent semiconductor. Heat it to just a few degrees higher, however, and it becomes a reflective metal. The semiconducting and metallic states actually have different crystalline structures. Among a number of possible applications, people have experimented with using vanadium dioxide film as the active ingredient in thermochromic windows that can block sunlight when the temperature soars and as microscopic thermometers that could be injected into the body.

In 2005, a research collaboration teaming Haglund and René Lopez (now at the University of North Carolina, Chapel Hill) with Andrea Cavalleri and Matteo Rini from the Lawrence Berkeley National Laboratory tested the vanadium dioxide transition with an ultrafast laser that produced 120-fs pulses.

Using this laser, the researchers determined that VO2 film can flip from transparent to reflective in a remarkably short time: less than 100 fs. This was the fastest phase transition ever measured. However, the mechanism that allowed it to make such rapid transitions remained a matter of scientific debate.

Now, in a two-year collaboration with the Leitenstorfer group, the Vanderbilt researchers have used a laser with even shorter (12-fs) pulses to "strobe" the vanadium dioxide transition with the fastest pulses ever used for this purpose. The result?

"This transition takes place even faster than we thought possible," Haglund says. "It can shift from transparent to reflective and back to transparent again in less than 100 femtoseconds, making the transition more than twice as fast as we had thought."

To identify the driving mechanism for the rapid change of state in vanadium dioxide, Leitenstorfer's graduate student Carl Kübler developed a method that converts the near-infrared photons produced by their 12-fs laser into a broad spectrum of infrared wavelengths that bracket a well-known vibration in the vanadium dioxide crystal lattice. At the same time, the Vanderbilt researchers figured out how to grow VO2 film on a diamond substrate that is transparent to infrared light.

This allowed the researchers to show that the energy in the laser beam goes directly into the crystal lattice of the VO2, driving it to shift from its transparent, crystalline form to its more compact and symmetric metallic configuration.

The laser light doesn't produce this shift by heating the VO2 lattice until it melts, as the conventional wisdom about phase transitions suggested. Instead, the researchers found that the stream of photons directly drive the oxygen atoms from one position to another by a process that is rather like pumping a swing in time with its natural frequency.

"People have believed for a long time that what happened in this phase transition was that the electrons get excited and then, somehow or another, the crystal structure changes," Haglund says. "But it turns out that the change in crystal structure is associated with this coherent molecular vibration."

Such a rapid transition is only possible because the difference between the metallic and semiconductor geometries is extremely small. This mechanism also allows the researchers to trigger the transition without changing the film's temperature.

"We can focus the laser beam on a transparent vanadium dioxide film and create a small reflective spot. We can switch it on and off in less than 100 fs provided we haven't dumped so much energy into the film that we've heated it up. However, the more laser energy you dump in the VO2, the longer it takes to return to the semiconducting state," Haglund says.

Henri Ehrke and Rupert Huber from the University of Konstanz and Andrej Halabica from Vanderbilt University also collaborated in the study.

About the Author

LFW Staff

Published since 1965, Laser Focus World—a brand and magazine for engineers, researchers, scientists, and technical professionals—provides comprehensive global coverage of optoelectronic technologies, applications, and markets. With 80,000+ qualified print subscribers in print and over a half-million annual visitors to our online content, we are the go-to source to access decision makers and stay in-the-know.

Sponsored Recommendations

Request a quote: Micro 3D Printed Part or microArch micro-precision 3D printers

April 11, 2024
See the results for yourself! We'll print a benchmark part so that you can assess our quality. Just send us your file and we'll get to work.

Request a free Micro 3D Printed sample part

April 11, 2024
The best way to understand the part quality we can achieve is by seeing it first-hand. Request a free 3D printed high-precision sample part.

How to Tune Servo Systems: The Basics

April 10, 2024
Learn how to tune a servo system using frequency-based tools to meet system specifications by watching our webinar!

Precision Motion Control for Sample Manipulation in Ultra-High Resolution Tomography

April 10, 2024
Learn the critical items that designers and engineers must consider when attempting to achieve reliable ultra-high resolution tomography results here!

Voice your opinion!

To join the conversation, and become an exclusive member of Laser Focus World, create an account today!